[New Product] SR First Class Coat
Next-generation glass coating born from five commitments
Developed from a solvent-free, inorganic paint that uses organopolysiloxane as the main ingredient, without using organic resins or volatile organic compounds (VOCs). Curing is accelerated at room temperature by the humidity and temperature in the air, and the inorganic bonds, which are stronger than conventional organic bonds, form a dense, tough, and inert film. We have created an ultra-durable glassy coating that is heat resistant, difficult to change due to ultraviolet light and light energy wavelengths, and is acid resistant. It truly is a "first class coating".
Release date: January 29, 2024 ~
Material: VOC free
Because it protects your precious car, we are particular about using materials that are safe for both your car and the environment.
A solvent-free, inorganic glass coat that does not use organic resins or volatile organic compounds (VOCs).
beauty
We paid particular attention to the beauty of the finish.
The film of First Class Coat produces a deep gloss that is as if it had been coated with another layer of clear.
Excellent stain resistance
We focused on making it stain resistant and easy to remove.
First Class Coat's coating is resistant to material changes due to UV rays and other light rays, is heat resistant, acid resistant, and shuts out various stains.
durability
We paid special attention to durability to ensure long-lasting beauty and stain resistance.
The inorganic bonds, which are stronger than conventional organic bonds such as waxes and polymers, form a dense, tough, and inert film, and the water-repellent effect lasts for about six months, and the film itself lasts for about two years*.
*Varies depending on parking environment, number of car washes, driving conditions, etc.
Maintainability
We focused on ease of care.
For daily care, washing with water or shampooing is sufficient.
It is combined with a water-repellent component that lasts for about six months, but even if the water-repellent effect wears off, the glass coating underneath will still firmly protect your car.
Good workability
Easy construction! No degreaser required! Shampoo applied to wet car body after car wash. Even on dark-colored cars, it doesn't get uneven and is easy to wipe off.
[Possible locations]
Automobile body painting parts, bumpers, wheels, headlight covers, rear light covers, other plastic resin parts, other metal parts
○Please perform all construction indoors. If it is unavoidable to install the product outdoors, avoid direct sunlight and avoid dust and foreign matter from adhering to it due to wind, etc.
○Separate the construction blocks for the roof, bonnet, trunk, side of the body, etc., and perform construction for each block according to the steps below.
In case of high temperature and high humidity, please divide it into smaller pieces.
Step 1: Sprinkle with water
*Please cool down the body by pouring enough water on it before starting work.
First, remove water stains and other dirt to prepare the base.
After that, wash the car with shampoo and wipe it roughly, leaving some water droplets behind. If it's been a while since you washed your car and it's completely dry, spray it with water.
At this time, make sure not to spray too much, just enough to make it slippery.
Step ② Dripping coating agent
Next, shake the coating agent in the container well, twist the tip of the cap to open it, and drip an appropriate amount onto the construction surface. As a guideline for the amount to be dripped, press the container lightly and apply about 3 drops onto an A4-sized area. Also, place drops on the sponge side in places where it is difficult to drip, such as on sloped surfaces.
Step 3: Apply coating agent
Immediately apply the coating agent using the sprinkled water.
Move the special sponge vertically, horizontally, vertically, horizontally to spread it evenly and evenly.
There is no need to use force.
Once applied, please perform the next step of ``wiping off'' before commenting (within 5 minutes).
Step 4 Wipe up
*Please note that if too much time passes after application, it will not be able to be wiped off and will become uneven.
Carefully wipe off any excess with a cloth dampened with clean water.
Please change the side of the cloth for wiping each block.
After that, wipe it dry with a soft flannel cloth for a better finish.
After wiping, let it dry for 1 to 2 hours and you're done. A shine will appear.
Do not expose to water for 24 hours immediately after installation. Also, please refrain from washing your car for 1 to 2 weeks after installation.
*The above construction is a "wet construction method". For automobile painted surfaces, etc., please use the "wet method", which is easy to work with and does not easily cause scratches.
If you want to thicken the coating when applying to wheels, etc., or to areas where water cannot be used, such as mobile phones, do not apply water, but instead apply an appropriate amount of the coating agent, spread it with a kitchen towel or tissue paper, and wipe it off. Please perform construction (dry construction method).
Construction set for 1 first class coat
Contents
①First class coat (10g) x 1
②Sponge x 1
③Microfiber cloth YS x 1
④Sticker x 1
Product number SR-FCCSET
JAN CD:4996327109716
Suggested retail price: 6,380 yen (5,800 yen excluding tax)
○Name: Clear paint ○Application: Multi-purpose protective film formation ○Ingredients: Organopolysiloxane ○Contents: 10g ○Dangerous goods classification: Class 4, Class 3 petroleum (water-insoluble), danger class III
